2009 Hummer H2 Door Panel Removal

How to remove Door panel on 2009 Hummer H2.

The complete procedure with diagram is explained below:----

The front and rear door panel removal :----


The procedure is basically the same for both sides front or rear:---
The procedure starts here.See Component Name listed below and compare with the diagram shown below the procedure:----

1) Front Side Door Inside Handle Bezel Finish Cover
2) Front Side Door Pull Handle Cover
3) Front Side Door Locking Rod Knob Assembly

Procedure
Ensure the locking rod is in the unlocked position.
Use a flat-bladed tool to disengage the detent tab and then remove the knob by pulling upward.
When re-installing, push the knob down until the detent tab touches the locking rod opening cover.
Push the detent tab into the lock knob to locking rod.


4) Front Side Door Trim Panel Bolt (Qty: 3)
 Tighten
2 N·m (18 lb in)

5)Front Side Door Trim Panel Assembly

Procedure
Disengage retainer.
Use a door trim pad removal tool to aid in the removal of the trim panel.
Disengage the door lock cable.
Disconnect the electrical connectors.
Transfer parts as necessary.

The help diagram is shown below:----




NOW THE REAR SIDE DOOR PANEL REMOVAL DIAGRAM:---



This will help.
Thanks.

Users Who Viewed This Problem Also Viewed:

How to remove the door panel to install a new window regulator?
http://howtobyme.blogspot.com/2011/08/how-to-remove-door-panel-to-install-new.html


window motor, regulator and door panel removal?
http://technoanswers.blogspot.com/2011/02/ford-explorer-window-motor-regulator.html


How to Remove Door Panels ?
http://repairhelpcenter.blogspot.com/2011/11/how-to-remove-door-panels-on-acura.html

How to Access car door panel?
http://howtobyme.blogspot.com/2011/11/how-to-access-car-door-panel.html

Vehicle door panel components? 
http://howtobyme.blogspot.com/2011/11/vehicle-door-panel-components.html

For All types of Car models and brands help 
Go to Newly Launched

FREE Car repair guide? 
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html 

& 
Complete Car repair Help FREE? 

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html

2000 Dodge Ram 3500 Cummins Diesel: Oil Leak issues?

The oil leak is noticed between Vacuum Pump and Power steering Pump.

Yes many others too have noticed this.

First understand the theory.


There is an insert/sleeve of sorts right behind the seal that is in the rear of the vacuum pump.

The insert/sleeve should be pulled out along with the seal out the rear of the vacuum pump and then the new seal installed and then the insert/sleeve should be re-installed.


There is a seal kit for the vacuum pump. You have to remove the vacuum and poower steering pumps and replace the seals.The kit is available at auto parts store. It costs $104, there are instructions in the kit.To follow the procedure.

Some users only replace the faulty seal,instead of replacing all seals.
As per there say,why to replace all seals when only one or two are worn out and faulty.At local parts store one seal costs approx $7 and complete kit comes for $104.

But i suggest replacing all seals.Because first getting faulty is indication,that others are also nearing towards end.But still if you get confirmed that other seals are still good,then replacing only the faulty seal is not a bad idea.


You will still need the gasket between the vacuum pump and the timing cover, and I beleive another seal for when you disassemble the vacuum pump, plus the shaft seal. That is why everything comes in a kit.

To remove the pump follow the instructions mentioned below:---------
Here are the instructions on removing the pump. After  the pump is out remove the boltls that hold the pump together, seperate the pump halves. Drive the seal out by using a socket and hammer, drive the seal out with the pump drive rotor. Clean it all up, put the pump drive back in, drive the new seal in, and reassemble.


REMOVAL

Disconnect battery negative cables.
Position drain pan under power steering pump.
Disconnect vacuum and steering pump hoses.
Disconnect lubricating oil feed line from fitting at underside of vacuum pump
Remove lower bolt that attaches pump assembly to engine block
Remove bottom, inboard nut that attaches adapter to steering pump. This nut secures a small bracket to engine block. Nut and bracket must be removed before pump assembly can be removed from block.
Remove upper bolt that attaches pump assembly to engine block
Remove pump assembly from vehicle.

NOTE: The vacuum pump and adapter are serviced as an assembly and must not be seperated.
Remove the remaining three power steering pump to adapter mounting nuts
Gently, remove the steering pump from the adapter. Use caution not to damage the oil seal in the adapter body .
NOTE: Make sure the two pump spacers are present before assembling power steering pump to adapter.
Aline the steering pump drive dog with the slot in the vacuum pump drive assembly, slide the steering pump into place on the adapter.Use care not to damage the oil seal in the adapter body.
Install the three steering pump to adapter nuts, do not install the lower inboard mounting nut at this time. Tighten nuts to 24 N·m (18 ft. lbs.).
Position new gasket on vacuum pump mounting flange Use Mopar® Perfect Seal, or silicone adhesive/sealer to hold gasket in place.
Insert pump assembly upper attaching bolt in mounting flange and gasket. Use sealer or grease to hold bolt in place if necessary.
Position pump assembly on engine and install upper bolt Tighten upper bolt only enough to hold assembly in place at this time.
Working from under vehicle, install pump assembly lower attaching bolt. Then tighten upper and lower bolt to 77 N·m (57 ft. lbs.).
Position bracket on steering pump inboard stud. Then install remaining adapter attaching nut on stud. Tighten nut to 24 N·m (18 ft. lbs.).
Connect oil feed line to vacuum pump connector and tighten line fitting.
Connect steering pump pressure and return lines to pump. Tighten pressure line fitting to 30 N·m (22 ft. lbs.).
Connect vacuum hose to vacuum pump.
Connect battery cables, if removed.
Fill power steering pump reservoir and Purge air from steering pump lines

See the help diagram shown below:-----


Both the parts are numbered and shown in the diagram
1 - PUMP MOUNTING FLANGE
2 - PUMP GASKET (APPLY SEALER TO BOTH SIDES)


Also see more help diagram




1 - PUMP ASSEMBLY LOWER MOUNTING BOLT
2 - ADAPTER BRACKET
3 - BOTTOM-INBOARD ADAPTER BRACKET NUT

Also view the power steering shaft and oil seal parts diagram and location




The parts shown in-the diagram are as follows:---

1 - PUMP SHAFT
2 - VACUUM FITTING
3 - VACUUM PUMP DRIVE
4 - OIL SEAL
5 - MOUNTING BRACKET
6 - DRIVE DOG
7 - PUMP SPACERS

This details will help.
Thanks.

Users Who Viewed This Problem Also Viewed:

Common Causes of Car Oil Leaks?

http://schematicsdiagram.blogspot.com/2011/12/common-causes-of-car-oil-leaks.html

Troubleshoot Car Oil leak?

http://schematicsdiagram.blogspot.com/2011/12/troubleshoot-car-oil-leak.html

Toyota Highlander Sport Oil change details?

http://repairhelpcenter.blogspot.com/2012/01/toyota-highlander-sport-oil-change.html

Low oil pressure light on Dodge Magnum? 
http://howtobyme.blogspot.com/2011/11/low-oil-pressure-light-on-dodge-magnum.html 

Kia Sportage leaking oil from oil pan? 
http://howtobyme.blogspot.com/2011/11/kia-sportage-leaking-oil-from-oil-pan.html 
Car Turns OFF due to low oil pressure warning light?

http://schematicsdiagram.blogspot.com/2011/12/car-turns-off-due-to-low-oil-pressure.html

Toyota Corolla leaking oil from timing cover?

http://technoanswers.blogspot.in/2012/02/toyota-corolla-leaking-oil-from-timing.html

Overfilling oil in engine?

http://whatisbyme.blogspot.in/2012/06/overfilling-oil-in-engine.html

For All types of Car models and brands help 
Go to Newly Launched

FREE Car repair guide? 
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html 

& 
Complete Car repair Help FREE? 

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html

Tail light Not working on 2002 Chevy Trailblazer

TAIL LIGHT / REVERSE LIGHT FUSE LOCATION.


For tail light not working,inspect the tail light fuse.
The fuse is located n the rear fuse box.

Get more help,with this diagram shown below:----

Check TBC fuse 32 in the rear fuse box for being blown. 


See hat fuse is for which part.Its a complete fuse box diagram;-----
See fuse number 32 in the diagram.its for tail light.



This diagram will help.
Thanks.

2001 Chevy Tracker Fuse Box Diagram

On Chevrolet Tracker there are  two fuse panels.
The first one is under the hood on the passenger side inner fender forward of the battery.
The second is under the dash on the drivers side.

Below is the fuse diagram shown for both fuse panels.

Also what fuse controls which part in your car,that is also mentioned in the chart.

UNDER-HOOD FUSE BOX

The Under dash INSTRUMENT PANEL FUSE BOX DIAGRAM

This both diagrams will help.

Thanks.

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

Honda Headlight Assembly Removal

The procedure for Old model Honda HeadLight assembly Removal.

In this chapter the details and help diagrams are also provided for Pre-1995 after 1995 and Latest Honda Head light bulb removal and diagrams.Please View that also.This will give you complete idea about what difference is there between today's Honda Headlamp assembly and old model Honda Head Lamp assemblies.


The complete detailed step by step procedure.

The details covers MAIN TOPIC Honda Accord/Prelude 1984-1995.
AND OTHER MISCELLANEOUS TOPICS FOR Honda/Prelude after 1995 and very Latest headlamp difference.

The Front Bumper has to be removed,that gives you complete and easiest access to replace headlight assembly.

Dont pull Headlight assembly,once you view it.There are delicate connectors that are to be disconnected first.Its a plug in/plug out type wire connectors.First disconnect the connectors,then remove screws and you can now remove complete headlight assembly.

Headlights

First Know and Understand About the Bulb/Headlamps:---

There are two general styles of headlamps, the sealed beam and replaceable bulb type. The sealed beam is by far the most common and includes almost all of the circular and rectangular lamps found on vehicles built through the 1980s. The sealed beam is so named because it includes the lamp (filament), the reflector and the lens in one sealed unit. Sealed beams are available in several sizes and shapes. All Honda vehicles covered in this information except the 1990-95 Accord and 1992-95 Prelude use sealed beam headlights. These latest Accords and Preludes use replaceable bulbs in fixed housings.

NOW GO THROUGH THE 

REMOVAL & INSTALLATION PROCEDURE

Sealed Beams.

To understand the procedure 

See Figures 1, 2, 3, 4, 5 and 6

FIG : Fig. 1: Headlamp mounting on 1984-85 Accords

Fig. 2: Headlamp mounting on 1986-89 Accords and 1984-91 Preludes

CAUTION:--- Most headlight retaining rings and trim bezels have very sharp edges. Wear gloves. Never pry or push on a headlamp; it can shatter suddenly.Go slow and do it carefully.

Some car models have popping up or spring retracting headlamps.

On cars with pop-up or retracting headlamps, turn the ignition switch OFF . Operate the retractor switch on the dash to bring the headlight doors up. The headlights should be off when the doors are up.
Remove the headlight bezel (trim).

On 1984-85 Accord, the trim involves the one piece lamp surround and corner molding.

Fig. 3: Remove the screws securing the headlight bezel

The sealed beam is held in place by a retainer and either 2 or 4 small screws. Identify these screws before applying any tools. Do not confuse the small retaining screws with the larger aiming screws. There will be two aiming screws or adjustors for each lamp. (One adjustor controls the up/down motion and the other controls the left/right motion.) Identify the adjustors and avoid them during removal. If they are not disturbed, the new headlamp should be in identical aim to the old one.
Using a small screwdriver (preferably magnetic) and a pair of needle-nose pliers if necessary, remove the small screws in the headlamp retainer.

Fig. 4: Remove the screws securing the retaining ring. Be sure not to disturb the adjusting screws

A HELPFUL TIP:---A good kitchen or household magnet placed on the shank of the screwdriver will provide enough grip to hold the screw during removal.


Remove the retainer and the headlamp may be gently pulled free from its mounts. Detach the connector from the back of the sealed beam unit and remove the unit from the car.

Fig. 5: Remove the retaining ring ...

Fig. 6: ... then unplug the connector from the back of the lamp. Be sure to transfer the rubber boot to the new lamp


FOLLOW THIS PROCEDURE
To install:
Once the old faulty bulb/lamp is removed out.now its tiome to install new headlamp.please buy exact bulb.There are many quality bulb available.But the exact bulb,which is supporting your cars headlight assembly.

1. Place the new headlamp in position and connect the wiring harness. Remember to install the rubber boot on the back of the new lamp. Also, make sure the headlight is right-side up.
2. Have an assistant turn on the headlights and check the new lamp for proper function, checking both high and low beams before final assembly.
3. Install the retainer and the small screws that secure it.
4. Reinstall the headlight trim.The procedure is done.
5. 
   

NOW THE PROCEDURE TO BE FOLLOWED ON 

1. Replaceable Bulb HEADLIGHT ASSEMBLY

For more help please view  Figure 7 which is shown below:----
Disconnect the negative battery cable.
Raise and prop the hood.
Remove any components necessary to access the lamp.

Fig. 7: Late model Accords and Preludes are equipped with replaceable bulb headlamps
just remove the screws,,the assembly will pull out.

There are three flanges that attach to the Honda, two beneath the lamp and one on the side near the signal lense. The diagram shows bullet like or bolts that go into the flanges. You  need to remove the bolts through the flanges before pulling assembly.

TO BE FOLLOWED SAFETY INSTRUCTIONS:----

Unplug the connector from the back of the lamp. The connector may be very tight and require wiggling to loosen; support the lamp while with your other hand while wiggling the connector loose. Turn the retaining ring counterclockwise, then pull the bulb from the lamp housing.
1. 
   
FOLLOW THIS INSTALLATION PROCEDURE:------------ To install:
2. 
   
3. WARNING:=====
Hold the new bulb by the base; do not touch the glass part with fingers or gloves. The grease left on the glass will form hot spots and shorten the life of the bulb. If the glass is accidentally touched, clean the glass with alcohol.

Install the new bulb. Make certain all three guide tabs fit into their correct slots. Turn the ring clockwise to lock it in place. Engage the wiring connector firmly. Connect the negative battery cable and turn the headlights on. Check both high and low beam function. Reinstall any components removed for lamp access.

Also see this Diagram Showing Today's Latest Model Headlight Assembly.
The Front bumper fender has to be out.


On this latest model that is after 2000 to 2008 year models.

It shouldn't take you more than 10 minutes or so to get the bumper off, there will be 16 push pins to remove, 4 bolts, and 2 screws, nothing too difficult. Once you have all of the fasteners out you just pull out on the back of the bumper near the wheels, it'll pop out of the groove it sits in.

First you'll need to remove the front bumper, this illustration will show you all the fasteners you'll need to remove.

Once you have the bumper off it's pretty straight forward to remove the headlamp assembly. just remove the bolts as shown in this illustration.

Now once you have the headlamp unbolted.Then all basics needs to be follows that is  unplug the connectors, remove it and install the new headlamp assembly, replacing all of the bolts you removed, then reinstall the bumper.

This details will help.

Thanks.

Users Who Viewed This Problem Also Viewed:

Headlight Assembly Removal on 2010 buick lacrosse?

http://technoanswers.blogspot.in/2012/04/headlight-assembly-removal-on-2010.html

Headlights flickering and car hesitates to start?

http://howtobyme.blogspot.in/2012/02/headlights-flickering-and-car-hesitates.html

Hummers headlights flashes while start?

http://technoanswers.blogspot.in/2012/02/hummers-headlights-flashes-while-start.html

Using non-AFS headlamp assembly for AFS assembly?

http://schematicsdiagram.blogspot.in/2012/02/using-non-afs-headlamp-assembly-for-afs.html

Only high beams work but head lights not working on Ford F350?

http://howtobyme.blogspot.com/2011/11/only-high-beams-work-but-head-lights.html

Only high beams working on GMC Savana?

High beams stopped working but headlights still work?

http://howtobyme.blogspot.com/2011/11/highbeams-stopped-working-but.html

      

Only one head light works on 2001 Dodge Caravan?

http://howtobyme.blogspot.com/2011/11/only-one-head-light-works-on-2001-dodge.html

For All types of Car models and brands help 
Go to Newly Launched

FREE Car repair guide? 
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html 

& 
Complete Car repair Help FREE? 

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html

Saturn SL2 Starter Wiring Diagram?

Starter wiring diagram details for 1999 Saturn SL2.
Starter not working will cause no start problems on your car.Problems like ...............
Vehicle just making click-- click sound or starter not engaging.
In this cases the starter has to be replaced.
FOR SATURN Replacing starter procedure .
In some cases starter wiring connections go wrong and this causes the problem.
So once the old starter is removed.Before installing new starter.Note down its correct wiring.
But if you have not done that and confused now,about how the wiring goes Don't worry,
For your help,the detailed starter wiring diagram is provided.
There are two diagrams showing different aspects of starter wiring.
The diagram is as follows:-----



One more diagram showing which wire to notice while installing new starter:----


This both diagrams will help you.
Thanks.

Users Who Viewed This Problem Also Viewed:

1999 Chrysler Cirrus: 8 IGN Fuel Starter Fuse Blows?

http://whatisbyme.blogspot.in/2012/06/1999-chrysler-cirrus-8-ign-fuel-starter.html

How to replace Starter on Infiniti Q45?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-starter-on-infiniti-q45.html

2006 GM Montana: How to replace Starter Solenoid?

http://repairhelpcenter.blogspot.in/2012/06/2006-gm-montana-how-to-replace-starter.html

Car turns over, but only starts, if starter is jumped?

http://schematicsdiagram.blogspot.com/2011/12/car-turns-overbut-only-startsif-starter.html

For All types of Car models and brands help 
Go to Newly Launched

FREE Car repair guide? 
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html 

& 
Complete Car repair Help FREE? 

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html

2004 Dodge Intrepid: How to replace Thermostat?

Where is thermostat located and how to replace it.

Its not a easy procedure to replace thermostat.

If you have a faulty thermostat, your engine will either overheat or not get hot enough.


The thermostat is located on the lower left side of the engine closer to the front of the engine.
To replace thermostat you will need to put it on a hoist and probably remove the engine mount and/or alternator to get to the thermostat housing.That's the only access to replace thermostat.

See the diagram shown below for thermostat location :----



This details will help.
Thanks.

Users Who Viewed This Problem Also Viewed:

Procedure to replace Dodge Sprinter Thermostat?

http://fordrepairhelp.blogspot.in/2012/04/procedure-to-replace-dodge-sprinter.html

How to Replace Thermostat on Dodge and Chrysler?

http://fordrepairhelp.blogspot.in/2012/04/how-to-replace-thermostat-on-dodge-and.html

How to replace Thermostat on Acura Car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-thermostat-on-acura-car.html

How to Replace Thermostat on 2007 Ford Taurus?

http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-thermostat-on-2007-ford.html

How to replace thermostat on Ford Windstar?

http://howtobyme.blogspot.in/2012/03/how-to-replace-thermostat-on-ford.html

How to replace Thermostat on Ford E series?

http://fordrepairhelp.blogspot.in/2012/03/how-to-replace-thermostat-on-ford-e.html

How To Replace Thermostat on Ford Expedition and Lincoln Navigator?

http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-thermostat-on-ford.html

How to replace Thermostat On Ford Mustang?

http://schematicsdiagram.blogspot.in/2012/03/how-to-replace-thermostat-on-ford.html

How to Replace Thermostat on Toyota Avalon & Camry?

http://howtobyme.blogspot.in/2012/03/how-to-replace-thermostat-on-toyota.html

Toyota Celica, Corolla, ECHO & MR2 THERMOSTAT Replacing details? Also location and diagram of thermostat is Provided?

http://schematicsdiagram.blogspot.in/2012/03/toyota-celica-corolla-echo-mr2.html

For All types of Car models and brands help 
Go to Newly Launched

FREE Car repair guide? 
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html 

& 
Complete Car repair Help FREE? 

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html