How to remove control panel on Bmw 325?

E30 Models

1. Disconnect the negative battery terminal. Remove the left side lower instrument panel trim and the center console tray. Remove the radio.
2. Remove the switches or covers from the openings above the radio opening. Disconnect the switches from the wiring harness.
3. Remove the screws holding the control panel at the top. The screws are accessible at the openings above the radio opening. Pull the control panel forward.
4. Disconnect the cable clamps and remove the cable ends from the levers.

To install:

1. Connect the cables. Install the panel into the dashboard and replace the screws.
2. Install the switches and the radio. Install the center console tray and the trim panel. Connect the negative battery terminal.

Defogger Flap & Fresh Air Flap

1. Disconnect the negative battery terminal. Remove the left side lower instrument panel trim and the center console tray. Lower the glove compartment door and disconnect the straps. Remove the radio.
2. Remove the switches or covers from the openings above the radio opening. Disconnect the switches from the wiring harness.
3. Remove the screws holding the control panel at the top. The screws are accessible at the openings above the radio opening. Pull the control panel forward.
4. Disconnect the cable clamp and remove the cable end from the lever. Do this at each end of the cable.

To install:

1. Connect the cable at the flap lever and fit the clamp in place. The cable housing must be flush with the clamp.
2. Connect the control lever cable and move the lever fully to the right. Turn the cable sleeve until the cable can be placed in the holder and the clamp secured.
3. Affix the control panel and replace the switches and covers. Install the radio, console tray, glove compartment door straps and the trim panel. Connect the negative battery terminal.

Footwell Flap

1. Disconnect the negative battery terminal. Remove the left side lower instrument panel trim and the center console tray. Remove the radio.
2. Remove the switches or covers from the openings above the radio opening. Disconnect the switches from the wiring harness.
3. Remove the screws holding the control panel at the top. The screws are accessible at the openings above the radio opening. Pull the control panel forward.
4. Disconnect the cable clamp and remove the cable end from the lever. Do this at each end of the cable.

To install:

1. Connect the cable at the flap lever and fit the clamp in place. The cable housing must be flush with the clamp.
2. Connect the control lever cable and move the lever fully to the right. Turn the cable sleeve until the cable can be placed in the holder and the clamp secured.
3. Affix the control panel and replace the switches and covers. Install the radio, console tray and the trim panel. Connect the negative battery terminal.

Mixing Flap

1. Disconnect the negative battery terminal. Remove the left side lower instrument panel trim and the center console tray. Lower the glove compartment door and disconnect the straps. Remove the radio.
2. Remove the switches or covers from the openings above the radio opening. Disconnect the switches from the wiring harness.
3. Remove the screws holding the control panel at the top. The screws are accessible at the openings above the radio opening. Pull the control panel forward.
4. Disconnect the cable clamp and remove the cable end from the lever. Do this at each end of the cable.

To install:

1. Connect the cable at the flap lever and fit the clamp in place.
2. Connect the temperature selector wheel cable end and move the wheel to the WARM position. Turn the cable knurl nut so the flap moves to theWARM position. Adjust the nut so the cable can be placed in the holder and the clamp secured.
3. Affix the control panel and replace the switches and covers. Install the radio, console tray, glove compartment door straps and the trim panel. Connect the negative battery terminal.

E36 Models

1. Insert a feeler gauge blade between the bottom of the trip computer display and the frame at the right side. Move the blade towards the right to release the display. Disconnect the wiring from the display and remove.
2. Remove the ashtray or lower console bin, as equipped, by pulling out.
3. Remove the knobs from the heater control panel. Remove the panel mounting screws in the depressions for the knobs and pull the panel out.
4. Push the controls back and guide downwards to be able to disconnect the wiring, shaft and cable.

To install:

1. Connect the shaft, wiring and cable to the control panel.
2. Guide the panel into place and install the mounting screws. Replace the knobs.
3. Install the ashtray or bin by pressing into place. Connect the wiring to the trip computer display and press into place.

Fresh Air Flap

1. Insert a feeler gauge blade between the bottom of the trip computer display and the frame at the right side. Move the blade towards the right to release the display. Disconnect the wiring from the display and remove.
2. Remove the ashtray or lower console bin, as equipped, by pulling out.
3. Remove the knobs from the heater control panel. Remove the panel mounting screws in the depressions for the knobs and pull the panel out.
4. Push the controls back and guide downwards to be able to disconnect the wiring, shaft and cable.
5. Place the vents above the glove compartment straight forward and remove from the dashboard.
6. Remove the 6 screws holding the glove compartment and remove the unit.
7. Disconnect the cable from the retainer and squeeze the tabs together to remove the cable from the holder.

To install:

1. Connect the wiring, cable and shaft to the control panel. Install the panel and knobs. Install the ashtray or bin and the trip computer display.
2. Install the cable into the holder and the retainer.
3. Turn the blower control to 4 and press the control lever towards the holder. This will adjust the cable.
4. Install the glove compartment and vents.

--------------

To Order car parts online:--To get heavy discount on car parts .Click this link below:----

http://technoanswers.blogspot.com/2011/05/from-where-to-order-car-parts-online.html

For car error code diagnosis click the link below:---

http://www.automd.com/diagnose/?amdcid=apwldrbrd1

Car no start:--

http://technoanswers.blogspot.com/2011/05/car-will-turn-over-but-will-not-start.html