How to remove Wheel Bearings on Honda odyssey?

Inspection

The wheel bearings are not adjustable.

1. Raise the vehicle, and support it with safety stands in the proper locations.
2. Remove the wheels, then reinstall the wheel nuts.
3. Attach the dial gauge. Place the dial gauge against the hub flange.
   
   
   

   

   Fig. Place the dial gauge against the hub flange

4. Measure the bearing end play by moving the disc inward or outward. If the bearing end play measurement is more than 0-0.05 mm (0-0.002 in.), replace the wheel bearing.

Removal & Installation

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove the knuckle.
3. Separate the hub (A) from the knuckle (B) using the special tool and a hydraulic press. Be careful not to distort the splash guard. Hold onto the hub to keep it from falling when pressed clear.
   
   
   

   

   Fig. Separate the hub (A) from the knuckle (B) using the special tool and a hydraulic press-2001-04 models

   
   
   
   

   

   Fig. Separate the hub (A) from the knuckle (B) using the special tool and a hydraulic press-2005-06 models

4. Remove the snap ring (A) and the splash guard (B) from the knuckle (C).
   
   
   

   

   Fig. Remove the snap ring (A) and the splash guard (B) from the knuckle (C)

5. Press the wheel bearing (A) out of the knuckle (B) using the special tools and a press.
   
   
   

   

   Fig. Press the wheel bearing (A) out of the knuckle (B) using the special tools and a press-2001-04 models

   
   
   
   

   

   Fig. Press the wheel bearing (A) out of the knuckle (B) using the special tools and a press-2005-06 models

6. Press the wheel bearing inner race (A) from the hub (B) using the special tool, commercially available bearing separator (C), and a press.
   
   
   

   

   Fig. Press the wheel bearing inner race (A) from the hub (B) using the special tool, commercially available bearing separator (C), and a press-2001-04 models

   
   
   
   

   

   Fig. Press the wheel bearing inner race (A) from the hub (B) using the special tool, commercially available bearing separator (C), and a press-2005-06 models

To install:

1. Wash the knuckle and hub thoroughly in high flash point solvent before reassembly.
2. Press a new wheel bearing (A) into the knuckle (B) using the old bearing (C), a steel plate (D), the special tools, and a press. Place the wheel bearing on the knuckle with the magnetic encoder side (black color) facing toward the inside. Be careful not to damage the magnetic encoder.
   
   
   

   

   Fig. Press a new wheel bearing (A) into the knuckle (B) using the old bearing (C), a steel plate (D), the special tools, and a press. Place the wheel bearing on the knuckle with the magnetic encoder side (black color) facing toward the inside

3. Install the snap ring (A) securely in the knuckle (B).
4. Install the splash guard (C), and tighten the screws (D).
   
   
   

   

   Fig. Install the snap ring (A) securely in the knuckle (B). Install the splash guard (C), and tighten the screws (D)

5. Install the hub (A) onto the knuckle (B) using the special tools shown and a hydraulic press. Be careful not to distort the splash guard (C).
   
   
   

   

   Fig. Install the hub (A) onto the knuckle (B) using the special tools shown and a hydraulic press. Be careful not to distort the splash guard (C)-2001-04 models

   
   
   
   

   

   Fig. Install the hub (A) onto the knuckle (B) using the special tools shown and a hydraulic press. Be careful not to distort the splash guard (C)-2005-06 models

To Order car parts online:--To get heavy discount on car parts .Click this link below:----

http://technoanswers.blogspot.com/2011/05/from-where-to-order-car-parts-online.html

For car error code diagnosis click the link below:---

http://www.automd.com/diagnose/?amdcid=apwldrbrd1

Car no start:--

http://technoanswers.blogspot.com/2011/05/car-will-turn-over-but-will-not-start.html