@

Thursday, December 15, 2011

Crankshaft Damper Replacement on Honda?

Crankshaft Damper 

Removal & Installation


The procedure is as follows:----

This procedure requires the use of the following special tools, or their equivalents:


Holder handle 07JAB-001020A
Holder attachment, 50 mm, offset 07MAB-PY3010A
Socket, 19 mm 07JAA-001020A

  1. Note the radio security code and station presets.
  2. Disconnect the negative battery cable.
  3. Raise and safely support the vehicle.
  4. Remove the right front wheel and tire assembly.
  5. Remove the lower engine splash shield.
  6. Remove the accessory drive belt, as outlined in this section.
  7. Hold the crankshaft pulley with Honda Tool Nos. 07MAB-PY3010A Holder Attachment and 07JAB-001020A Holder Handle or their equivalents, then remove the crankshaft pulley bolt by turning it in a counterclockwise direction with a 19mm socket and breaker bar.

    Click image to see an enlarged view
    Fig. Hold the pulley with holder handle (A) and holder attachment (B). Remove the bolt with a heavy duty 19mm socket (C) and breaker bar
  8. Remove the crankshaft pulley.
To install:
  1. Clean the pulleys, crankshaft, bolt and washer. Lubricate with new engine oil as shown.
    WARNING
    Never use an impact wrench to tighten the crankshaft pulley bolt.



    Click image to see an enlarged view
    Fig. Clean the pulleys (A), crankshaft (B), bolt (C) and washer (D). Lubricate with new engine oil as shown
  2. Install the crankshaft pulley, then tighten the bolt, as follows:
    1. Hold the pulley with the holder handle and holder attachment, then tighten the bolt to 47 ft. lbs. (65 Nm) with a torque wrench and heavy duty 19mm socket.
    2. Mark the bolt head and crankshaft pulley as shown, then tighten the bolt an additional 60° (The mark on the bolt head should line up with the mark on the crankshaft pulley).

      Click image to see an enlarged view
      Fig. Hold the pulley with the holder handle (A) and holder attachment (B), then tighten the bolt to 47 ft. lbs. (65 Nm) with a torque wrench and heavy duty 19mm socket (C)


      Click image to see an enlarged view
      Fig. Mark the bolt head (D) and crankshaft pulley (E) as shown, then tighten the bolt an additional 60 degrees. The mark on the bolt head should line up with the mark on the crankshaft pulley
  3. Install the drive belt, as outlined in this section.
  4. Install the splash shield.
  5. Install the right front tire/wheel.
  6. Connect the negative battery cable, then enter the security code for the radio.

-----------
This details will help you.
----------
If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

------------
See below related help solutions:----

Camshaft, Bearings & Lifters Replacing on Honda Odyssey?

http://howtobyme.blogspot.com/2011/12/camshaft-bearings-lifters-replacing-on.html


How to Replace Crankshaft Pulley on Audi A4 and VW Passat?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-crankshaft-pulley-on.html

How the timing marks on valve pulleys line up with crank on 1997 Dodge Intrepid?

http://howtobyme.blogspot.com/2011/11/how-timing-marks-on-valve-pulleys-line.html



No comments:

Post a Comment