@

Showing posts with label auto repair solutions. Show all posts
Showing posts with label auto repair solutions. Show all posts

Monday, December 5, 2011

Ford Keyless Remote Fob Reprogramming?

If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.


If keyfob is faulty or keyfob battery is weak,then reprogramming procedure will not get complete.
Here are the instructions.
1. Turn ignition to RUN or ACC.
2. Momentarily jump pins in programming connector located in LR quarter panel area (Connector will not be plugged into anything, it will have two pins inside it, if you have to unlug it you have the WRONG one. Not all vehicles are set up from factory for keyless remotes) All doors will lock then unlock to confirm programming mode.
3. Press any button on first keyless remote. Door locks will cycle to confirm programming.
4. If programming a second keyless remote, press any button on second keyless remote.
Door locks will cycle to confirm programming.
5. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
This details will help.Thanks.
------------

1995 Oldsmobile Eighty Eight has bad O2 Sensor?

http://schematicsdiagram.blogspot.com/2011/12/1995-oldsmobile-eighty-eight-has-bad-o2.html

Dual Exhaust on 1996 Chevrolet camaro z28?

http://schematicsdiagram.blogspot.com/2011/12/dual-exhaust-on-1996-chevrolet-camaro.html

How to adjust rpm on 2009 dodge charger SRT8?

http://schematicsdiagram.blogspot.com/2011/12/how-to-adjust-rpm-on-2009-dodge-charger.html

Car takes time to Crank and start?

http://howtobyme.blogspot.com/2011/12/car-takes-time-to-crank-and-start.html

Car jerks while going uphill and Check engine light is ON?


Car turns over, but only starts, if starter is jumped?


Service Engine Soon light stays on?


Gasoline around gas cap?


Car will not run after resetting inertia switch on Mercury Mystique?

VAN emits whitish bluish smoke and bad fuel smell from exhaust

Car cigarette lighter fuse blows out?

CD MECH ERROR?

Car will not go into 4WD high or 4WD low?

Truck is hard to start and Emits smoke while starting?

Engine cuts out at 3000 RPM?

Car turns over but will not start, only makes clicking sound?

Catalytic Converter glowing hot?

After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?


Fuel gauge jumps from empty to full?


Why airbag light flashes 7 times?

Passenger side Folding Mirror is not operating?

Very low air output on Chevrolet Trailblazer?

After replacing battery, ignition not working?

Where is Fuse box located on 2002 Honda Accord?

 

How to reset Radio code after car battery is died?


Car still runs Rough after tune up?

Car cranks, has spark but will not start?

Cylinder 6 Misfire?

Chevy s-10 blazer 4.3l Spark Plug Firing Order?

2008 Ford Ranger Shifter Knob Removal?

Erratic idle on car?

Car dies when gas pedal is pressed?

MAF, IAT, MAP and Coolant Level Sensor problem all together on Mazda MPV?

Car Surging?

How to replace a distributor on Chevrolet Camaro?

Cadillac Seville Digital Dash Display not working?

Can car radio code block Passkey anti theft system ?

Friday, December 2, 2011

Fuel gauge jumps from empty to full?

If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.



Very common problem,faced by many car users.The Fuel SENDING UNIT has failed. And is causing this Fluctuation of the gauge,The Sending Unit Is mostly Located IN the FUEL TANK & Requires TANK REMOVAL to Replace it,
NOTE: ----IF YOU HAVE HAD THE FUEL PUMP REPLACED RECENTLY, THEN 99% PROBABILITY THAT THE INSTALLER WAS NOT VERY GENTEL WITH IT, THIS IS A COMMON REASON FOR THIS TYPE OF FAILURE.
The details will help.
Thanks,.
----------------
Check the list of car problems and solutions mentioned below for more help:-----


Car jerks while going uphill and Check engine light is ON?


Car turns over, but only starts, if starter is jumped?


Service Engine Soon light stays on?


Gasoline around gas cap?


Car will not run after resetting inertia switch on Mercury Mystique?

VAN emits whitish bluish smoke and bad fuel smell from exhaust

Car cigarette lighter fuse blows out?

CD MECH ERROR?

Car will not go into 4WD high or 4WD low?

Truck is hard to start and Emits smoke while starting?

Engine cuts out at 3000 RPM?

Car turns over but will not start, only makes clicking sound?

Catalytic Converter glowing hot?

After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?



Car will not run after resetting inertia switch on Mercury Mystique?


If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.


Recheck inertia switch.It some cases car starts but again stops running after few days,this is because inertial switch gets triggered again.
Did the inertia switch get triggered again? On the side panel, down behind the hood-release, there is an access hole in the panel. (1.5in diameter?) Inside you'll find the switch. It's a round button; that acts kind of like the ground default switch on an outlet. If you can push it in; it's been triggered again. If not; well it should be fine.
What triggered it the first time? If it was an accident; there may be further damage.
If that's good to go: I'd have to ask whether the fuel filter was changed at the same time. Sometimes they can clog with debris from burnt-out pump.
Also check the plug connecting to the pump. That would be worth checking as well. You need to pull up the rear seat cushion. Where you'll find a rubber cap with a wiring harness protruding from it. Lift that up you'll find the plug underneath. Unplug it and perform a visual inspection. If it all looks good, well you'll need to begin more advanced diagnostics by car pro in your area.
This basic details will help you.Thanks.
----------------
For more car problems and solutions,check the list below:-----

---------

The car will not start?

-----------------

Car will not crank?


-----------

Car has no spark?


-------------

How to troubleshoot car battery?

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?



-----------

car will turn over but will not start?



-----------------

Car wont start?


----------


Thursday, December 1, 2011

Car jerks while going uphill and Check engine light is ON?


If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

This problems needs to be scanned to confirm.
It sounds like a sensor is intermittantly loosing the data stream. Since the engine light came on, I would go to a reputable shop and have them check for codes. Many auto parts stores will do this as well and sometimes for free. Can't beet free. If I were to guess I would say something like the camshaft postion sensor is going bad, Or the crankshaft postion sensor, Or something like that. The code will tell which one it is.
This will help.
Thanks.
---------------

For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

-----------------

Car will not crank?


-----------

Car has no spark?


-------------

How to troubleshoot car battery?

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?



-----------

car will turn over but will not start?



-----------------

Car wont start?


----------

Tuesday, November 29, 2011

Car AC belt makes Squeaking Noise?


If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

Ac belt squeaking noise,is noticed by many car users.The belt needs to be inspected.Either its worn out or its tension got loose or its alignment is wrong or pulleys are worn out.There are lots of possibilities.
The Belt of the a/c to the solenoid pulley or the main belts can create a lot of squeaking noise.
Start the car to hear the noise now pour some water into the belt and the noise will subside off . You have the noise confirmed of a belt as sometimes it will trick you to think of water pump bearings, alternator bearings or even engine noises.
Stop the engine and check for play in the belt if so tighten the belt If not use some chalk power or candle wax to be rubbed into the belt that was making the noise - the a/c drive belt - or the main belts..
Now start and check . the nosie would be reduced or gone.
You can have the belts changed sooner or later.
This details will help.Thanks.
----------------

For car AC related and Heater related solutions. You can refer the options mentioned below:---

Car AC Blows Warm Air ?


How to test AUTO AC pressure?


AUTO Air Conditioning Troubleshooting?



AUTO A/C COOLING PROBLEM?


Fixing refrigerant leak?


How to locate Car AC Refrigerant leak?


CAR AC INTERMITTENT COOLING?


What causes INTERMITTENT COOLING on Car AC system?


Car AC making Noise?


BAD ODOR ON CAR AIR CONDITIONER?



How to Recharge Car's Air Conditioner




For details regarding:--

How does Vehicles Engine cooling system works?


Engine cooling components working?


How to flush cars radiator?



For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

-----------------

Car will not crank?


-----------

Car has no spark?


-------------

How to troubleshoot car battery?

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?



-----------

car will turn over but will not start?



-----------------

Car wont start?


----------



Serpentine belt diagram for 2007 Toyota Tacoma?


If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

The belt diagram is shown below :----

Toyota: Model TACOMA Engine L4 2.7L 2694cc GAS FI N 2TRFE

Without A/C...


With A/C

----------

For all types of

Timing belt routing diagrams for cars and trucks?

Click the link below:---

For all types of 

Drive belt routing diagrams for cars and trucks?

Click the link below:---


For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

-----------------

Car will not crank?


-----------

Car has no spark?


-------------

How to troubleshoot car battery?

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?



-----------

car will turn over but will not start?



-----------------

Car wont start?


----------




How to replace valve cover gasket on 1997 chevy s-10?


If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

The procedure with details and diagrams is as follows :-----


  1. Disconnect the negative battery

    cable and remove the air duct assembly.

  2. Disconnect the throttle cable and remove the cable support linkage.
  3. If equipped, disconnect the cruise control cable assembly.
  4. Remove the PCV valve and pipe assembly.
  5. Tag and disconnect the spar

    k plug wires and move them out of the way.
  6. Disconnect the power br

    ake booster vacuum hose.
  7. Loosen and remove the rocker cover retaining bolts, then remove the cover from the engine.

DO NOT pry on the cover to remove it. If it sticks, use your palm or a rubber mallet to bump it rearwards, from the

front. 
  1. Using a putty knife, carefully clean the gasket mounting surfaces. Keep debris out of the engine.



Fig. Fig. 2: Unfasten the throttle linkage cover retaining bolt ...
 

Fig. Fig. 3: ... and remove the cover



Fig. Fig. 4: Disconnect the throttle cable from the linkage
 

Fig. Fig. 5: Use a suitable prytool to pry the cable retaining clip from the cable support bracket and slide the cable out of the bracket
 

Fig. Fig. 6: Unfasten the retainers attaching the front cable support bracket from the upper intake manifold and the valve cover
 

Fig. Fig. 7: Unfasten the rear cable support bracket bolt and set the cable and bracket aside
 

Fig. Fig. 8: Unscrew the crankcase vent valve retainer ...
 

Fig. Fig. 9: ... and pull the pipe and valve assembly from the valve cover
 
Fig. Fig. 10: Disconnect the PCV valve hose from the valve
 
Fig. Fig. 11: Disconnect the spark plug wires and move them aside

Fig. Fig. 12: Disconnect the brake booster vacuum hose clamp using pliers ... 
Fig. Fig. 13: ... and disconnect the hose, then set the hose assembly aside
 
Fig. Fig. 14: Remove the valve cover retaining bolts


Fig. Fig. 15: Lift the valve cover and move it backwards until it clears the hoses at the front of the engine, then remove the valve cover

To install:
  1. Install the rocker arm cover to the engine using a new gasket, then tighten the retainers to 89 inch lbs. (10 Nm). Be careful not to overtighten the fasteners and either distort the valve cover (causing and leak) or break the fastener (causing more work).
  2. Connect the spark plug wires.
  3. Install the PCV valve and pipe assembly.
  4. Connect the brake booster vacuum hose.
  5. If equipped, install the cruise control cable assembly.
  6. Connect the throttle cable and secure the cable support linkage. Tighten the bracket bolts to 10 ft. lbs. (25 Nm) and the bracket nut to 22 ft. lbs. (30 Nm).
  7. Connect the air duct to the inlet, then connect the negative battery cable.
-------------

This details will help.
Thanks.
---------------
For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

-----------------

Car will not crank?


-----------

Car has no spark?


-------------

How to troubleshoot car battery?

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?



-----------

car will turn over but will not start?



-----------------

Car wont start?


----------