schematics and diagrams: exhaust

Showing posts with label exhaust. Show all posts

Monday, December 19, 2011

AUTOMOTIVE EMISSIONS?

Automobile emissions control covers all the technologies that are employed to reduce the air pollution-causing emissions produced by vehicles exhaust system due to fuel burning and other possibilities.

Want to understand emission repairs? Want to perform automotive diagnosis quickly and accurately?

Go through this details:----

EMISSIONS TEST FAILURE (Smog Check failure).

Before emission controls were mandated on internal combustion engines, other sources of engine pollutants were discovered along with the exhaust emissions. It was determined that engine combustion exhaust produced approximately 60 percent of the total emission pollutants, fuel evaporation from the fuel tank and carburetor vents produced 20 percent, with the final 20 percent being produced through the crankcase as a by-product of the combustion process.

Now for more understanding,its recommended to go through this details:----

Thursday, December 15, 2011

How to replace Intake Manifold on 2008 Honda Odyssey?

Replace Intake Manifold on Honda vehicle is as follows :-----------

Intake Manifold

Removal & Installation

Remove the intake manifold cover.

Remove the air inlet duct.

Remove the PCV hose and brake booster hose.

Remove the EVAP canister hose and water bypass hoses. Plug the bypass hose.

Tag and disconnect all wiring connected to the manifold.

Remove the upper cover mounting bolts and nuts, in 2 equal steps, in the sequence shown. Remove the cover.

Fig. Upper cover loosening sequence-J35A6 and J35A7 engines

Remove the intake manifold mounting bolts and nuts, in 2 equal steps, in the sequence shown. Remove the manifold.

Fig. Intake manifold loosening sequence-J35A6 and J35A7 engines

Installation is the reverse of removal. Tighten the manifold bolts and nuts, in the sequence shown, in 2 equal steps, to 16 ft. lbs. (22 Nm). Tighten the cover bolts and nuts, in the sequence shown, in 2 equal steps, to 105 inch lbs. (12 Nm).

Fig. Intake manifold torque sequence-J35A6 and J35A7 engines

Fig. Upper cover torque sequence-J35A6 and J35A7 engines

Fig. Intake manifold and related parts-J35A6 engine

Fig. Intake manifold and related parts-J35A7 engine

-----------

This details will help you.

----------

--------------

How to replace Exhaust Manifold on Acura Car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-exhaust-manifold-on.html

How to replace Intake Manifold on Acura Car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-intake-manifold-on-acura.html

How to Remove Exhaust Manifold on ToyotaPrevia?

http://technoanswers.blogspot.com/2011/12/how-to-remove-exhaust-manifold-on.html

How to Remove Intake Manifold on Toyota Previa?

http://technoanswers.blogspot.com/2011/12/how-to-remove-intake-manifold-on-toyota.html

How to replace Exhaust Manifold in Audi and VW car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-exhaust-manifold-in-audi.html

How to replace Intake Manifold in Audi and VW car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-intake-manifold-in-audi.html

Exhaust Manifold?

THE PROCEDURE TO REPLACE MANIFOLD.

Removal & Installation

Remove the engine cover.

Remove the front A/F sensor (Sensor 1) and the front secondary HO2S (Sensor 2).

Remove the exhaust pipe A mounting nuts (front WU-TWC side).

Remove the A/C condenser fan assemblies.

Carefully remove the front WU-TWC.

To install:

Carefully install the front WU-TWC with a new gasket and new self-locking nuts. Tighten the nuts in a crisscross pattern in two or three steps to 23 ft. lbs. (31 Nm).

The remainder of the installation is the reverse order of removal.

------------

How to replace Exhaust Manifold on Acura Car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-exhaust-manifold-on.html

How to replace Intake Manifold on Acura Car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-intake-manifold-on-acura.html

How to Remove Exhaust Manifold on Toyota Previa?

http://technoanswers.blogspot.com/2011/12/how-to-remove-exhaust-manifold-on.html

How to Remove Intake Manifold on Toyota Previa?

http://technoanswers.blogspot.com/2011/12/how-to-remove-intake-manifold-on-toyota.html

How to replace Exhaust Manifold in Audi and VW car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-exhaust-manifold-in-audi.html

How to replace Intake Manifold in Audi and VW car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-intake-manifold-in-audi.html

Monday, December 12, 2011

Where is the EGR feedback sensor located on 2004 Ford Explorer ?

EGR means exhaust gas recirculation sensor.It is a sensor that is mounted to the EGR valve. It monitors the position of the EGR valve and sends that info to the ECM.

The EGR sensor is built into the EGR valve, which bolts to the side of the throttle body.If you are getting a trouble code for the sensor, first check the wiring carefully to make sure it hasn't touched a hot manifold or been otherwise damaged.

This is How the EGR sensor looks.

----------------------

This details will help you.

----------

For EGR EXHAUST help solutions,see the list below :---

How to Replace an EGR Valve

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-egr-valve.html

How to clean egr valve on Isuzu Amigo?

http://howtobyme.blogspot.com/2011/08/how-to-clean-egr-valve-on-isuzu-amigo.html

Inspecting and replacing Exhaust system on Acura Car models?

http://repairhelpcenter.blogspot.com/2011/11/inspecting-and-replacing-exhaust-system.html

VAN emits whitish bluish smoke and bad fuel smell from exhaust

http://schematicsdiagram.blogspot.com/2011/12/van-emits-whitish-bluish-smoke-and-bad.html

How to Replace an Exhaust Manifold Gasket

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-exhaust-manifold-gasket.html

How to Replace an Exhaust System

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-exhaust-system.html

Monday, December 5, 2011

Dual Exhaust on 1996 Chevrolet camaro z28?

If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

You have to take permission.Read the details as follows :----
Different states have different rules about this, call your local state office that runs the inspection program and ask them, in my state it is the Air resources board. If you just do it you may have to remove the pipes to pass smog inspection. You can never run true dual exhaust, you must retain the original catalytic converters, and on this car you have one main catalyst. You can however split the pipes out of the main catalyst and run duals that way, it will not improve performance very much but it helps.

This details will help you,Thanks.

-------------