How to remove timing chain on 2002 Toyota Camry ?

Timing Chain & Sprockets

Removal & Installation

2az-FE Engine

Fig. Exploded view of the timing chain and front cover components-2.4L (2AZ-FE) engine

1. Before servicing the vehicle, refer to the Precautions Section.
2. Drain the engine oil.
3. Remove or disconnect the following:
   
   
   Negative battery cable

   Hood

   Right-side front wheel

   Engine under covers

   Right-side fender apron seal

   Front exhaust pipe

   Engine moving control rod and bracket

   Right-side engine mounting stay and bracket

   Accessory drive belt

   Engine appearance cover

   Engine wire

   Alternator

   Power steering pump, leave the hoses connected

   Ignition coils

   Ventilation hoses

   Cylinder head cover
   
   
4. Turn the crankshaft pulley to set the No. 1 cylinder to TDC compression. Align the groove on the pulley with the timing mark -0- on the front cover.
5. Remove the crankshaft pulley as follows:
   1. TMC made: Use Special Tool 09213-54015 to hold the pulley to loosen the bolt. Use Special Tool 09950-50013 to remove the bolt and pulley.
   2. TMMK made: Use Special Tool 09960-10010 to hold the pulley to remove the bolt. Use Special Tool 09950-40011 to remove the crankshaft pulley
      
      
      

      

      Fig. Removing the crankshaft pulley-TMC-2.4L (2AZ-FE) engine

      
      
      
      

      

      Fig. Removing the crankshaft pulley-TMMK-2.4L (2AZ-FE) engine

   
   
6. Remove or disconnect the following:
   
   
   Crankshaft position sensor

   Lower oil pan

   No. 1 chain tensioner

   Accessory drive belt tensioner
   
   
7. Support the engine with a suitable engine lifting device.
8. Remove or disconnect the following:
   
   
   Engine mounting insulators

   Right-side engine mounting bracket

   Stud bolt for the accessory drive belt tensioner from the block

   Front cover mounting bolts and nuts

   Front cover

   Crankshaft position sensor plate

   Timing chain tensioner slipper

   Timing chain vibration damper

   Timing chain

   Crankshaft timing sprocket
   
   
9. Turn the crankshaft counterclockwise by 90°, and align an adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
   
   
   

   

   Fig. Align the adjusting hole of the oil pump drive sprocket with the oil pump groove-2.4L (2AZ-FE) engine

   
   
   
   

   

   Fig. Insert a bar to lock the sprocket in position-2.4L (2AZ-FE) engine

10. Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Remove the nut.
11. Remove the bolt, chain tensioner and spring.
12. Remove the chain tensioner, oil pump sprocket and No. 2 timing chain.

To install:

1. Set the crankshaft key into the left horizontal position. Turn the cutout of the drive shaft to the top.
   
   
   

   

   Fig. Align the crankshaft key and drive shaft cutout as shown for installation-2.4L (2AZ-FE) engine

2. Align the yellow colored links with the timing marks of the sprocket as shown in the illustration.
3. Insert the sprockets with chain to the crankshaft and oil pump shaft.
4. Temporarily tighten the oil pump driven sprocket with the nut.
5. Insert the damper spring into the adjusting hole, and install the chain tensioner plate with the nut. Tighten to 9 ft. lbs. (12 Nm).
6. Align the adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
7. Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Tighten the nut to 22 ft. lbs. (30 Nm).
8. Rotate the crankshaft counterclockwise by 90°, and align the crankshaft key to the top.
9. Install the timing chain vibration damper. Tighten to 80 inch lbs. (9 Nm).
10. Align the timing marks of the camshaft timing sprockets and bearing caps.
11. Using the crankshaft pulley bolt, turn the crankshaft and set the set key on the crankshaft upward.
12. Align the gold or orange colored link with the timing mark of the crankshaft timing sprocket.
13. Using Special Tool 09309-37010, tap in the sprocket.
14. Align the gold or yellow colored links with the timing marks of the camshaft timing gear and camshaft timing sprocket. Install the chain.
    
    
    

    

    Fig. Align the marks of the sprockets and bearing caps to set the No. 1 cylinder at TDC-2.4L (2AZ-FE) engine

    
    
    
    

    

    Fig. Set the crankshaft set key facing upward-2.4L (2AZ-FE) engine

    
    
    
    

    

    Fig. Align the marked link of the timing chain with crankshaft sprocket timing mark-2.4L (2AZ-FE) engine

    
    
    
    

    

    Fig. Tap the crankshaft sprocket in with Special Tool 09309-37010-2.4L (2AZ-FE) engine

    
    
    
    

    

    Fig. Align the marked links of the timing chain with the camshaft sprockets during installation-2.4L (2AZ-FE) engine

15. Install the timing chain tensioner slipper. Tighten to 14 ft. lbs. (19 Nm).
16. Install the crankshaft position sensor plate. The -F- mark faces forward.
17. Clean any old gasket material from the mating surfaces of the front cover, cylinder head and block.
18. Apply a continuous bead of sealant to the front cover mating surface either 0.10 in. (2.5 mm) or 0.12-0.16 (3-4 mm) in diameter as indicated in the illustration.
    
    
    

    

    Fig. Apply sealant to the front cover mating surface as shown-2.4L (2AZ-FE) engine

19. Install the front cover and tighten as follows:
    1. Bolt A and nuts: 80 inch lbs. (9 Nm).
    2. Bolts B: 15 ft. lbs. (21 Nm).
    3. Bolts C: 32 ft. lbs. (43 Nm).
       
       
       

       

       Fig. Bolt and nut identification for the front cover-2.4L (2AZ-FE) engine

    
    
20. Install or connect the following:
    
    
    Stud bolt for the accessory drive belt. Tighten to 7 ft. lbs. (10 Nm).

    Accessory drive belt tensioner. Tighten to 44 ft. lbs. (60 Nm).

    Right-hand engine mounting bracket. Tighten to 40 ft. lbs. (54 Nm).

    Engine mounting insulator. Tighten top bolt to 70 ft. lbs. (95 Nm) and bottom bolts to 64 ft. lbs. (87 Nm).

    Lower oil pan. Tighten bolts to 80 inch lbs. (9 Nm).

    Timing chain tensioner

    Crankshaft position sensor. Tighten to 80 inch lbs. (9 Nm).
    
    
21. Align the crankshaft pulley key set with the key groove of the pulley, and side on the pulley. Using the Special Tool previous used to remove, tighten the crankshaft pulley bolt to 125 ft. lbs. (170 Nm).
22. Turn the crankshaft counterclockwise and disconnect the plunger knock pin from the hook.
23. Turn the crankshaft clockwise and check that the slipper is pushed by the plunger.
24. The remainder of the installation is the reverse order of removal.
25. Refill the engine with oil to the correct level.
26. Start the engine and check for leaks.

2gr-FE Engine

Fig. Exploded view of the timing chain and front cover components-3.5L (2GR-FE) engine

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove the engine/transaxle assembly from the vehicle.
3. Remove the transaxle.
4. Remove the oil dipstick tube.
5. Remove the driveplate.
6. Install the engine to a suitable engine stand.
7. Remove or disconnect the following:
   
   
   Idler pulley

   Right-side engine mounting bracket

   Accessory drive belt tensioner

   Water pump pulley

   No. 2 timing gear cover

   Engine mounting stay and bracket

   Water inlet housing
   
   
8. Using Special Tool 09213-70011, hold the crankshaft pulley and loosen the pulley bolt.
9. Using the pulley bolt and Special Tool 09950-50013, remove the crankshaft pulley.
   
   
   

   

   Fig. Loosen the crankshaft pulley bolt with Special Tool 09213-70011-3.5L (2GR-FE) engine

   
   
   
   

   

   Fig. Remove the crankshaft pulley with Special Tool 09950-50013-3.5L (2GR-FE) engine

10. Remove or disconnect the following:
    
    
    Upper and lower oil pans

    O-rings from the oil pump

    Air intake surge tank

    Ignition coils

    Oil pipes

    Cylinder head cover
    
    
11. Remove the mounting bolts from the front cover.
12. Using a suitable pry tool with the tip covered with protective tape, pry the front cover in the specified locations to remove.
    
    
    

    

    Fig. Pry the front cover at the locations shown in the illustration-3.5L (2GR-FE) engine

13. Pry the front crankshaft seal from the front cover.
    
    
    

    

    Fig. Removing the seal from the front cover-3.5L (2GR-FE) engine

14. Temporarily tighten the pulley set bolt.
15. Set the timing mark on the crank angle sensor plate to the right-hand block bore center line to put the No. 1 cylinder at TDC.
16. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration. If not, turn the crankshaft one complete revolution (360°) and align the timing marks as shown.
17. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
18. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate-s hole.
19. Remove the chain tensioner.
20. Remove the chain tensioner slipper.
    
    
    

    

    Fig. Align the timing mark on the sensor plate and block to set the No. 1 cylinder at TDC-3.5L (2GR-FE) engine

    
    
    
    

    

    Fig. Ensure the timing marks of the camshaft timing gears are aligned with the bearing cap timing marks-3.5L (2GR-FE) engine

    
    
    
    

    

    Fig. Procedure to remove the timing chain tensioner-3.5L (2GR-FE) engine

21. Turn the crankshaft 10° counterclockwise to loosen the chain off the crankshaft timing gear.
22. Remove the timing chain from the crank timing gear and place it on the crankshaft.
23. Turn the camshaft timing gear on the right-side bank clockwise (approximately 60°). Be sure to loosen the chain between the center banks.
24. Remove the timing chain.
    
    
    

    

    Fig. Turn the crankshaft counterclockwise to loosen the timing chain-3.5L (2GR-FE) engine

To install:

1. Align the orange marked links and timing mark as shown in the illustration and install the timing chain.
2. Turn the camshaft timing gear on the right-side bank counterclockwise to tighten the chain between banks.
3. Align the yellow marked link and timing mark as shown in the illustration and install the chain onto the crankshaft timing gear.
4. Temporarily tighten the crankshaft pulley set bolt.
   
   
   

   

   Fig. Align the timing chain marked links with the camshaft timing gear marks to install-3.5L (2GR-FE) engine

   
   
   
   

   

   Fig. Align the timing chain marked link with the crankshaft gear to install-3.5L (2GR-FE) engine

5. Install the chain tensioner slipper.
6. Install the chain tensioner as follows:
   1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
   2. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.
   3. Install the chain tensioner and tighten the bolts to 7 ft. lbs. (10 Nm).
   4. Remove the lock pin of chain tensioner.

   
   
7. Check that each timing mark is aligned with the crankshaft at TDC compression.
8. Remove the pulley set bolt.
9. Using Special Tool 09316-60011 or equivalent seal driver, tap in a new front oil seal into the front cover until its surface is flush with the front cover case edge. Apply multi-purpose grease to the oil seal lip.
   
   
   

   

   Fig. Tap a new oil seal into place in the front cover-3.5L (2GR-FE) engine

10. Install the front cover as follows:
    1. Apply a continuous bead of sealant 0.118 in. (3 mm) in diameter to the engine as shown in the illustration.
    
    
    
    

    

    Fig. Apply sealant to the engine block as shown when installing the front cover-3.5L (2GR-FE) engine

    2. Apply sealant to the front cover as shown in the illustration.
       
       
       

       

       Fig. Apply sealant to the front cover as specified by the illustration-3.5L (2GR-FE) engine

    3. Install a new oil pump gasket.
    4. Align the oil pump-s drive rotor spline and the crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.
       
       
       

       

       Fig. Correct orientation of the oil pump rotor and crankshaft during installation of the front cover-3.5L (2GR-FE) engine

    5. Install the front cover and loosely install all of the mounting bolts and nuts. Bolts A are 1.57 in. (40 mm); Bolts B are 2.17 in. (55 mm); Bolts C are 0.98 in. (25 mm).
    6. Fully tighten the bolts in sequence as follows:
       
       
       Areas 1 and 2: 15 ft. lbs. (21 Nm)

       Area 3: 15 ft. lbs. (21 Nm)

       Area 4: 32 ft. lbs. (43 Nm) for Bolt A; 15 ft. lbs. (21 Nm) for all other bolts
       
       

       

       

       Fig. Bolt identification and torque sequence for the front cover-3.5L (2GR-FE) engine
       
       

    
    
11. The remainder of the installation is the reverse order of removal.
12. Start the engine and check for leaks.

-------------

For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-start.html

-----------------

Car will not crank?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-crank.html

-----------

Car has no spark?

http://schematicsdiagram.blogspot.com/2011/06/car-has-no-spark.html

-------------

How to troubleshoot car battery?

http://schematicsdiagram.blogspot.com/2011/06/how-to-troubleshoot-car-battery.html

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------

car will turn over but will not start?

http://technoanswers.blogspot.com/2011/05/car-will-turn-over-but-will-not-start.html

-----------------

The Brake Indicator Light Stays On dash of car?

http://schematicsdiagram.blogspot.com/2011/06/brake-indicator-light-stays-on-dash-of.html

The ABS and Traction Control Lights stays ON dash of car?

http://schematicsdiagram.blogspot.com/2011/06/abs-and-traction-control-lights-stays.html

Check Engine Light On car?

http://schematicsdiagram.blogspot.com/2011/06/check-engine-light-on-car.html

-------------------------

How to replace Interior Lights on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-interior-lights-on-car.html

Car lights not working, even after replacing the bulb/lamp?

Click this link below:--

http://schematicsdiagram.blogspot.com/2011/06/car-lights-not-working-even-after.html

---------------

How to replace head lights on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-head-lights-on-car.html

--------------------

How to replace Parking, turn, and Brake Lights on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-parking-turn-and-brake.html
How to remove the door panel on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-remove-door-panel-on-car.html

How to replace power window motor in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-power-window-motor-in.html

How to test relays on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-relays-on-car.html

-----------------------------

How to troubleshoot Engine Misfires?

http://schematicsdiagram.blogspot.com/2011/06/how-to-troubleshoot-engine-misfires.html

------------

The spark plug firing order for car?

http://schematicsdiagram.blogspot.com/2011/06/spark-plug-firing-order-for-car.html

------------------------

Where is the Thermostat located in car?

http://schematicsdiagram.blogspot.com/2011/06/where-is-thermostat-located-in-car.html

How to recharge AC on Auto/Truck/car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-recharge-ac-on-autotruckcar.html

-------------------

How to trouble shoot speedometer?

http://schematicsdiagram.blogspot.com/2011/06/speedometer-not-working.html

To Order car parts online:--To get heavy discount on car parts .Click this link below:----

http://technoanswers.blogspot.com/2011/05/from-where-to-order-car-parts-online.html

How to Replace Coil Springs?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-coil-springs.html

How to Replace an Oil Pan Gasket?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pan-gasket.html

How to Replace a Fuel Injector

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fuel-injector.html

How to Replace a C.O.P. Type Ignition Coil?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-cop-type-ignition-coil.html

How to Replace a Fuel Pressure Regulator?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fuel-pressure-regulator.html

How to Replace a Fuel Pump?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fuel-pump.html

How to Replace a Rear Lift Gate Locking Mechanism?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-lift-gate-locking.html

How to Clean a Fuel System

http://schematicsdiagram.blogspot.com/2011/07/how-to-clean-fuel-system.html

How to Replace an Ignition Coil

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-ignition-coil.html

How to Replace a Windshield

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield.html

How to Replace a Mass Air Flow Sensor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-mass-air-flow-sensor.html

How to Replace a Rear Distance Sensor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-distance-sensor.html

How to Replace a Muffler

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-muffler.html

How to Replace an Engine

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-engine.html

How to Replace an Intake Manifold Gasket

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-intake-manifold-gasket.html

How to Replace an Oil Pump

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pump.html

How to Lubricate a Brake Pedal Linkage ?

http://schematicsdiagram.blogspot.com/2011/07/how-to-lubricate-brake-pedal-linkage.html

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

How to Replace a Distributor Cap

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-distributor-cap.html

How to Replace a Door Weather Stripping

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-door-weather-stripping.html

How to Replace a Freeze Plug

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-freeze-plug.html

How to Replace a Head Gasket

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-head-gasket.html

How to Replace a Heater Core

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-heater-core.html

How to Replace Spark Plugs?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-spark-plugs.html

How to Replace a Rear Axle Bearing?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-axle-bearing.html

How to Replace a Front Bumper Cover

http://technoanswers.blogspot.com/2011/07/how-to-replace-front-bumper-cover.html

How to Replace a Manual Transmission

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-manual-transmission.html

How to Replace a Headlight Bulb

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-bulb.html

How to Replace a Headlight Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-switch.html

How to Replace Windshield Wiper Blades

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-blades.html

How to Replace a Cooling Fan

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-cooling-fan.html

How to Replace a Catalytic Converter

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-catalytic-converter.html

How to Replace an Engine Mount

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-engine-mount.html

How to Replace a Fog Light Assembly

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fog-light-assembly.html

How to Change Engine Oil and Filter

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-engine-oil-and-filter.html

How to Replace a Power Seat Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-seat-switch.html

How to Replace a Rear Main Seal

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-main-seal.html

How to Repair a Defroster Grid

http://schematicsdiagram.blogspot.com/2011/07/how-to-repair-defroster-grid.html

How to Replace an AWD Transfer Case

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-awd-transfer-case.html

How to Replace a Plastic License Plate Bracket?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-plastic-license-plate.html

How to Replace a Power Seat Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-seat-motor.html

How to Replace Power Steering Fluid

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-steering-fluid.html

How to Replace a Power Window Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-window-switch.html

How to Replace a Quarter Glass Panel?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-quarter-glass-panel.html

How to Pressure Test a Radiator and Cap

http://schematicsdiagram.blogspot.com/2011/07/how-to-pressure-test-radiator-and-cap.html

How to Replace a Radiator

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-radiator.html

How to Repair a Hood.

http://schematicsdiagram.blogspot.com/2011/07/how-to-repair-hood.html

How to Replace an Energy Absorber

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-energy-absorber.html

How to Replace Heater Core Hoses

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-heater-core-hoses.html

How to Replace a Thermostat.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-thermostat.html

How to Rotate Tires.

http://schematicsdiagram.blogspot.com/2011/07/how-to-rotate-tires.html

How to Replace Wheel Lug Nuts

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-wheel-lug-nuts.html

How to Replace a Tire Valve Stem

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-tire-valve-stem.html

How to Change a Flat Tire

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-flat-tire.html

How to Replace Leaf Springs

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-leaf-springs.html

How to Replace a Heater Control Valve

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-heater-control-valve.html

How to Replace Transmission Cooler Lines

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-transmission-cooler.html

How to Replace an Ignition Control Unit

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-ignition-control-unit.html

How to Replace a Brake Hose

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-brake-hose.html

How to Replace a Transfer Case Rear Output Seal

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-transfer-case-rear.html

How to Replace a Seat Belt and Seatbelt Retractor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-seat-belt-and-seatbelt.html

How to Replace a Power Steering Rack

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-steering-rack.html

How to Bleed Brakes with a Tool

http://schematicsdiagram.blogspot.com/2011/07/how-to-bleed-brakes-with-tool.html

How to Replace a Tail Light Bulb

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-tail-light-bulb.html

How to Check Automatic Transmission Fluid Level

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

How to Change Automatic Transmission Fluid and Filter

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

How to Replace Vacuum Hoses

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-vacuum-hoses.html

How to Replace an Air Intake Boot

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-air-intake-boot.html

How to Replace a Valve Cover Gasket

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-valve-cover-gasket.html

How to Replace a Water Pump

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

How to Replace a Windshield Wiper Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-switch.html

How to Replace Window Run Channel Seals

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-run-channel-seals.html

How to Replace a Window Regulator

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-regulator.html

How to Balance a Tire and Wheel

http://schematicsdiagram.blogspot.com/2011/07/how-to-balance-tire-and-wheel.html

How to Replace a Window Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-motor.html

How to Adjust a Hood Release Latch?

http://schematicsdiagram.blogspot.com/2011/07/how-to-adjust-hood-release-latch.html

How to Replace a Radiator Support

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-radiator-support.html

How to Replace a Rear Pinion Seal.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-pinion-seal.html

How to Replace Battery Cables

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-battery-cables.html

How to Replace a Proportioning Valve

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-proportioning-valve.html

How to Replace an Upper Radiator Hose

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-upper-radiator-hose.html

How to Replace a Lower Radiator Hose

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-lower-radiator-hose.html

How to Replace a Timing Belt?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-timing-belt.html

How to Check for Loose or Worn Suspension

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-for-loose-or-worn.html

How to Check for Loose Steering System

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-for-loose-steering-system.html

How to Replace an Oil Pressure Switch (Sensor)

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pressure-switch.html

How to Replace a Fender Liner or Splash Shield

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fender-liner-or-splash.html

How to Replace a Hood Insulator

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-hood-insulator.html

How to Replace a Rear Differential.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-differential.html

How to Repair a Hood Hinge

http://schematicsdiagram.blogspot.com/2011/07/how-to-repair-hood-hinge.html

How to Replace a Brake Pedal Return Spring

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-brake-pedal-return.html

How to Replace a Door Shell.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-door-shell.html

How to Replace a Transfer Case Front Output Seal

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-transfer-case-front.html

How to Replace a Hood Latch/Lock Assembly

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-hood-latchlock-assembly.html

How to Replace a Lift Gate Strut

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-lift-gate-strut.html

How to Replace Mud Flaps (Mud Guards)

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-mud-flaps.html

How to Check Differential Oil Leaks and Replace Oil.

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-differential-oil-leaks-and.html

How to Replace a Mirror

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-mirror.html

How to Replace a Transfer Case Shift Linkage

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-transfer-case-shift.html

How to Replace a Transmission Mount

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-transmission-mount.html

How to Replace a U-Joint

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-u-joint.html

How to Replace a Washer Tank

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-washer-tank.html

How to Replace an A/C Line or Hose

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-ac-line-or-hose.html

How to Replace a Heater and A/C Blower Motor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-heater-and-ac-blower.html

How to Replace an ABS Control Unit

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-abs-control-unit.html

How to Perform a Brake Adjustment

http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-brake-adjustment.html

How to Replace an Alternator Belt

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-alternator-belt.html

How to Replace an Emblem

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-emblem.html

How to Replace an Exhaust Manifold Gasket

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-exhaust-manifold-gasket.html

How to Replace a Tail Pipe

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tail-pipe.html

How to Replace Shock Absorbers

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-shock-absorbers.html

How to Replace a Strut Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-strut-assembly.html

How to Replace a Driveshaft

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-driveshaft.html

How to Replace a Wheel Cylinder

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-wheel-cylinder.html

How to Replace a Hood

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-hood.html

How to Replace a Brake Disc (Rotor)

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-brake-disc-rotor.html

How to Replace a Metal License Plate Bracket

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-metal-license-plate.html

How to Replace a Power Steering Pump

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-power-steering-pump.html

How to Perform a Basic Engine Tune-Up

http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up.html

How to Perform a Basic Engine Tune Up-Oil Change

http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up-oil.html

How to Perform a Basic Engine Tune Up-Spark Plug and Wire Change

http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up_01.html

How to Replace a Distributor Cap and Rotor ?

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-distributor-cap-and.html

How to Repair a Valance

http://schematicsdiagram.blogspot.com/2011/08/how-to-repair-valance.html

How to Replace a Turn Signal Switch

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-turn-signal-switch.html

How to Replace a Plastic Bumper Cover

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-plastic-bumper-cover.html

How to Replace a Parking Brake Cable

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-parking-brake-cable.html

How to Replace Windshield Wiper Blade Refills

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-windshield-wiper-blade.html

How to Replace a Corner Light

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-corner-light.html

How to Replace a Bumper Bracket or Side Support

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-bumper-bracket-or-side.html

How to Replace a Washer Pump.

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-washer-pump.html

How to Replace a Grille

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-grille.html

How to Replace a Locking Hub

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-locking-hub.html

How to Replace a Fender

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fender.html

How to Replace a Power Steering Hose

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-power-steering-hose.html

How to Replace a Tailgate

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tailgate.html

How to Replace a Soft Top

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-soft-top.html

How to Replace a Carburetor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-carburetor.html

­

How to Replace a Bumper Trim

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-bumper-trim.html

How to Replace Trunk Strut

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-trunk-strut.html

How to Replace a Front End Cover

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-front-end-cover.html

How to Replace a Front Pipe

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-front-pipe.html

How to Replace an Antenna Mast

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-antenna-mast.html

How to Replace a Side Marker Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-side-marker-light.html

How to Install a Carpet on car?

http://schematicsdiagram.blogspot.com/2011/08/how-to-install-carpet-on-car.html

How to Replace a Spoiler

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-spoiler.html

How to Replace a Mirror Glass on car?

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-mirror-glass-on-car.html

How to Replace a Step Bumper?

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-step-bumper.html

How to Replace a Door Lock

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-door-lock.html

How to Replace a Throttle Body

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-throttle-body.html

How to Replace a Throttle Position Sensor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-throttle-position-sensor.html

How to Replace a Grille Insert

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-grille-insert.html

How to Replace a Fan Shroud Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fan-shroud-assembly.html

How to Replace an Engine Splash Shield

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-engine-splash-shield.html

How to Replace a Turn Signal Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-turn-signal-light.html

How to Replace a Headlight Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-assembly.html

How to Replace a Park Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-park-light-assembly.html

How to Replace an Expansion Tank

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-expansion-tank.html

How to Replace an Exhaust System

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-exhaust-system.html

How to Replace a Fender Trim

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fender-trim.html

How to Replace a Headlight Door

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-door.html

How to Replace a Fan Shroud

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fan-shroud.html

How to Replace a Harmonic Balancer

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-harmonic-balancer.html

How to Replace a Header Panel

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-header-panel.html

How to Replace a Fuel Tank

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fuel-tank.html

How to Replace a Fuel Tank Cap

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fuel-tank-cap.html

How to Replace a Distributor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-distributor.html

How to Replace an EGR Valve

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-egr-valve.html

How to Replace an Oxygen Sensor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-oxygen-sensor.html

How to Replace an Ignition Wire Set

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-ignition-wire-set.html

How to Replace a Tail Light

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tail-light.html

How to Replace a Door Handle

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-door-handle_18.html

How to Replace a Hood Strut

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-hood-strut.html

How to Replace Tail Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tail-light-assembly.html

How to Replace a Front Bumper

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-front-bumper.html

How to Replace a Fuel Pump Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fuel-pump-assembly.html

How to Replace an Axle Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-axle-assembly.html

How to Replace a Tailgate Handle

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tailgate-handle.html

How to Replace a Wheel Hub Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-wheel-hub-assembly.html

How to Replace a Control Arm

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-control-arm.html

How to Replace a Window Regulator with Motor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-window-regulator-with.html

How to Replace a Headlight

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight.html

How to Check the Brake Fluid Level

http://schematicsdiagram.blogspot.com/2011/08/how-to-check-brake-fluid-level.html

How to Replace a Parking Brake Switch

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-parking-brake-switch.html

How to Replace a Blower Motor Resistor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-blower-motor-resistor.html

How to replace frost plug on car?

http://howtobyme.blogspot.com/2011/08/how-to-replace-frost-plug-on-car.html

Horn stopped working?

http://howtobyme.blogspot.com/2011/08/horn-stopped-working.html

How to clean egr valve on Isuzu Amigo?

http://howtobyme.blogspot.com/2011/08/how-to-clean-egr-valve-on-isuzu-amigo.html

Cruise control stopped working?

http://howtobyme.blogspot.com/2011/08/cruise-control-stopped-working.html

Car is stuck in park and the shift will not move?

http://howtobyme.blogspot.com/2011/08/car-is-stuck-in-park-and-shift-will-not.html

How to change the outer door weather strip?

http://howtobyme.blogspot.com/2011/08/how-to-change-outer-door-weather-strip.html

Car slows down when it gets hotter?

http://howtobyme.blogspot.com/2011/08/car-slows-down-when-it-gets-hotter.html

Warning lights on and speedometer died?

http://howtobyme.blogspot.com/2011/08/warning-lights-on-and-speedometer-died.html

Car won't rev past 1900 rpms?

http://howtobyme.blogspot.com/2011/08/car-wont-rev-past-1900-rpms.html