If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.
If keyfob is faulty or keyfob battery is weak,then reprogramming procedure will not get complete.
Here are the instructions.
1. Turn ignition to RUN or ACC.
2. Momentarily jump pins in programming connector located in LR quarter panel area (Connector will not be plugged into anything, it will have two pins inside it, if you have to unlug it you have the WRONG one. Not all vehicles are set up from factory for keyless remotes) All doors will lock then unlock to confirm programming mode.
3. Press any button on first keyless remote. Door locks will cycle to confirm programming.
4. If programming a second keyless remote, press any button on second keyless remote.
Door locks will cycle to confirm programming.
5. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.1995 Oldsmobile Eighty Eight has bad O2 Sensor?
http://schematicsdiagram.blogspot.com/2011/12/1995-oldsmobile-eighty-eight-has-bad-o2.html
Dual Exhaust on 1996 Chevrolet camaro z28?
http://schematicsdiagram.blogspot.com/2011/12/dual-exhaust-on-1996-chevrolet-camaro.html
How to adjust rpm on 2009 dodge charger SRT8?
http://schematicsdiagram.blogspot.com/2011/12/how-to-adjust-rpm-on-2009-dodge-charger.html
Car takes time to Crank and start?
http://howtobyme.blogspot.com/2011/12/car-takes-time-to-crank-and-start.html
Car jerks while going uphill and Check engine light is ON?
Car turns over, but only starts, if starter is jumped?
Service Engine Soon light stays on?
Gasoline around gas cap?
Car will not run after resetting inertia switch on Mercury Mystique?
VAN emits whitish bluish smoke and bad fuel smell from exhaust
Car cigarette lighter fuse blows out?
CD MECH ERROR?
Car will not go into 4WD high or 4WD low?
Truck is hard to start and Emits smoke while starting?
Engine cuts out at 3000 RPM?
Car turns over but will not start, only makes clicking sound?
Catalytic Converter glowing hot?
After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?
Fuel gauge jumps from empty to full?
Why airbag light flashes 7 times?
Passenger side Folding Mirror is not operating?
Very low air output on Chevrolet Trailblazer?
After replacing battery, ignition not working?
Where is Fuse box located on 2002 Honda Accord?
How to reset Radio code after car battery is died?
Car still runs Rough after tune up?
Car cranks, has spark but will not start?
Cylinder 6 Misfire?
Chevy s-10 blazer 4.3l Spark Plug Firing Order?
2008 Ford Ranger Shifter Knob Removal?
Erratic idle on car?
Car dies when gas pedal is pressed?
MAF, IAT, MAP and Coolant Level Sensor problem all together on Mazda MPV?
Car Surging?
How to replace a distributor on Chevrolet Camaro?
Cadillac Seville Digital Dash Display not working?
Can car radio code block Passkey anti theft system ?
If keyfob is faulty or keyfob battery is weak,then reprogramming procedure will not get complete.
Here are the instructions.
1. Turn ignition to RUN or ACC.
2. Momentarily jump pins in programming connector located in LR quarter panel area (Connector will not be plugged into anything, it will have two pins inside it, if you have to unlug it you have the WRONG one. Not all vehicles are set up from factory for keyless remotes) All doors will lock then unlock to confirm programming mode.
3. Press any button on first keyless remote. Door locks will cycle to confirm programming.
4. If programming a second keyless remote, press any button on second keyless remote.
Door locks will cycle to confirm programming.
5. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
This details will help.Thanks.
------------
No comments:
Post a Comment